Topic
VFD
21 guides across the knowledge base.
Enclosure Heat Calculations
Estimating the temperature inside a control panel from the power its contents dissipate and the surface that carries it out, what to do when the answer is too hot, and why drives change everything.
8 min readUpdated Sep 5, 2026
Variable Frequency Drives in Pump Panels
What a drive adds to a pump panel and what it costs: speed control, soft start, reduced inrush, and diagnostics against heat, harmonics, cable and motor stress, bypass, and the minimum speed below which a pump does no work.
11 min readUpdated Sep 5, 2026
Distribution Pressure Control
How a booster or high service pump station holds discharge pressure with variable speed pumps, how pumps are staged, and what stops the system hunting.
9 min readUpdated Sep 5, 2026
Wet Well Level PID Control
Holding a wet well level with a variable speed pump instead of bang-bang control: the loop structure, the minimum speed floor, the stop and restart logic at low inflow, tuning for a slow integrating process, and where level PID is the wrong idea.
11 min readUpdated Sep 5, 2026
VFD Pump Control in Wastewater
The control modes for a variable speed wastewater pump: level control, flow pacing, fixed speed with soft start, and drawdown modes, plus the wastewater-specific rules: minimum speed, ragging at low speed, force main velocity, and the periodic full-speed run.
10 min readUpdated Sep 5, 2026
Booster Pump Stations
Inline stations that raise pressure from one zone to another: suction pressure protection, discharge pressure control with drives, staging, the hydropneumatic tank alternative, surge and check valve behavior, and the interlocks that keep a booster from collapsing the zone it draws from.
9 min readUpdated Sep 5, 2026
High Service Pumping
Pumping finished water into distribution: the control modes of tank level, pressure, and flow, how they interact with the clearwell and contact time, staging and surge, the telemetry the station depends on and its fallback, energy scheduling, and the alarms.
10 min readUpdated Sep 5, 2026
High Service Pumps
The pumps that carry finished water into distribution: types, the pump curve against the system curve, best efficiency point, the affinity laws and where a drive pays, parallel operation, valves, protection, and the efficiency monitoring that shows wear.
11 min readUpdated Sep 5, 2026
Documenting Firmware Versions
Why the firmware version of every controller, module, drive, switch, radio, and instrument belongs in the inventory with the date it was read: advisories are issued by version. Where to read each one, the several versions one controller has, and the cadence.
8 min readUpdated Sep 5, 2026
Firmware Management
Updating the firmware of controllers, modules, drives, HMIs, switches, and radios without breaking the plant: why firmware lags and why it still matters, tracking versions, deciding what to update and when, and the update as a planned outage with a rollback.
9 min readUpdated Sep 5, 2026
Drive Will Not Start in AUTO
The drive runs from the keypad or in HAND but not from the controller. The command source, the enable and safe torque off inputs, the speed reference, and the network control word, checked in the order that finds the problem fastest.
9 min readUpdated Sep 5, 2026
Drive Faults on Overcurrent
An overcurrent trip on a variable frequency drive: what the drive measured and when, the difference between a trip at start, during acceleration, at steady speed, and at deceleration, the motor and cable faults behind each, the parameter settings that cause nuisance trips, and the tests that separate them.
9 min readUpdated Sep 5, 2026
Drive Faults on Overvoltage
A DC bus overvoltage trip on a drive: where the bus voltage comes from, why deceleration and a driving load raise it, the utility-side causes from a high supply and capacitor switching, the deceleration ramp and overvoltage controller settings, braking resistors, and how to tell a regeneration trip from a supply transient.
9 min readUpdated Sep 5, 2026
Motor Will Not Reach Speed
A drive that runs but never gets the motor to the commanded speed: the reference and its scaling, the maximum frequency and speed limits, current limit holding the ramp, a load beyond the motor, a wrong motor parameter set, and a low supply, with the drive readouts that separate them.
9 min readUpdated Sep 5, 2026
Drive Trips on Ground Fault
A ground fault trip on a variable frequency drive: how the drive detects it, the motor and cable insulation faults behind most trips, the submersible cable problem, the capacitive leakage on long cables and filters that produces nuisance trips, wiring errors, and the insulation test that decides it.
9 min readUpdated Sep 5, 2026
Cable Routing Problems
Noise that comes from where a cable runs: signal cables sharing a conduit, tray, or wireway with power or drive cables, long parallel runs, and shallow crossings. How coupling works, the separations that prevent it, and how to find the shared path.
9 min readUpdated Sep 5, 2026
VFD Noise on Analog Signals
Analog readings that jump or wander when a drive runs, and speed references that make a drive hunt: how the drive output couples into signal wiring, why the input turns kilohertz noise into a slow wander, the tests that pin it on the drive, and the fixes.
10 min readUpdated Sep 5, 2026
Drive Causes Instrument Noise
When many instruments became noisy after a drive was installed, the drive installation is the place to look: the checklist for motor cable, shielding, grounding, filters, and carrier frequency that decides how much noise a drive puts into the plant.
10 min readUpdated Sep 5, 2026
Panel Overheating
A panel that runs hot: drives tripping on temperature in the afternoon, controllers faulting in summer, components discolored, a fan that never stops. The causes from an undersized enclosure to a clogged filter, measuring the rise, and the fixes.
8 min readUpdated Sep 5, 2026
Voltage Sag on Motor Start
Lights dim, contactors drop, and controllers reset every time the big pump starts: the starting current of an across-the-line motor pulling down a weak source. Measuring the sag, checking the source, and fixing it with a soft starter or ride-through.
8 min readUpdated Sep 5, 2026
Interference on Channel
Data lost on a strong-signal path: another system on the frequency, a nearby transmitter overloading the receiver, intermodulation on a shared tower, drive noise, or a stuck transmitter. How to measure the noise floor, find the source, and cure it.
8 min readUpdated Sep 5, 2026
Other topics
Direct contact
Have a controls question?
Reach Eric Sullivan directly about anything on this site, a controls or automation topic, or one of his personal projects.