Symptom
A process value shows exactly its minimum or maximum, or a value beyond range, and does not move; the controller input reports under-range, over-range, or open wire; a related alarm or interlock has acted; the loop current reads at a rail or at a fault value.
The short answer
Signal Pegged High or Low
A loop signal that is stuck at an end of its range is reporting one of three things: the process is genuinely at or beyond the range limit, the transmitter has detected a fault and driven the loop to its configured alarm current, or the loop itself is broken or miswired so that the receiver sees no current or full current. Measuring the loop current with a meter separates them: a fault current below 3.8 or above 20.5 milliamps is the transmitter announcing a diagnostic, exactly 0 milliamps is an open loop or a dead supply, a current at the supply limit is a short, and a clean 4.0 or 20.0 is a process value at the limit or a range that no longer fits the process. The receiver display alone cannot tell these apart, which is why the meter comes first.
Key points
- Measure the current: a fault current is a diagnostic, 0 is an open loop, the supply limit is a short, 4.0 or 20.0 is a limit or a range problem.
- Transmitters signal faults with currents outside the live range, and the fault code on the transmitter says what they found.
- A process can really be out of range; check the field before condemning the instrument.
- A range that does not fit the process pegs the signal at full scale whenever the process exceeds it.
- An input channel that is clamped, scaled wrong, or faulted looks pegged when the loop is fine.
Possible causes and what to check
| Possible cause | What to check |
|---|---|
| Transmitter fault current | The loop reads below 3.8 or above 20.5 milliamps at a value fixed by the alarm setting; the transmitter display or a handheld communicator shows the fault: sensor open, electronics, over-range, or a configuration error. |
| Process truly at or beyond range | The loop reads a clean 4.0 or 20.0 and a field indicator or a portable instrument confirms the process is at the limit; the range is too narrow or the process is abnormal. |
| Open loop | Zero current: a broken wire, a loose terminal, a blown loop fuse, a dead loop supply, or a transmitter with no power. Check the supply voltage at the transmitter terminals. |
| Short or ground on the loop | Current at the supply limit or a high, unstable value; a wire shorted to ground or to another conductor, or water in a junction box. Isolate segments. |
| Reversed polarity | Zero current with the supply present; the transmitter connected backwards after a replacement. Check the terminal marking. |
| Range set wrong in the transmitter | The transmitter range narrower than the process; the signal pegs at 20 whenever the process exceeds the upper range value. Compare the transmitter range with the design range and the controller scaling. |
| Sensor failure | A pressure element ruptured, a level probe fouled, a flow tube empty, an electrode broken; the transmitter may report a fault or a plausible-looking rail. Inspect the sensor. |
| Input channel fault or clamp | The loop current is normal at the terminals but the controller shows a rail; the channel is faulted, its range set wrong, or its scaling clamps at a limit. Check the module diagnostics and scaling. |
| Loop supply overloaded | Several transmitters on one supply and not enough voltage for the loop resistance; signals peg or sag together. Measure the supply under load. |
| Isolator or signal conditioner failed | A device in the loop passing full or zero output; measure on both sides of it. |
What the current says
| Measured loop current | Meaning | Next step |
|---|---|---|
| 0.0 mA | Open loop, no supply, or reversed transmitter | Supply voltage at the transmitter; continuity; polarity |
| About 3.6 mA or below 3.8 | Transmitter low fault alarm | Read the transmitter fault code |
| Exactly 4.0 mA, steady | Process at or below lower range value | Confirm in the field; check the range |
| Between 4 and 20, but the controller shows a rail | Input channel, scaling, or a clamp | Module diagnostics and scaling |
| Exactly 20.0 mA, steady | Process at or above upper range value | Confirm in the field; check the range |
| 21 to 22.5 mA | Transmitter high fault alarm or over-range | Read the transmitter fault code |
| At the supply limit or wandering high | Short or ground fault on the loop | Isolate segments; check junction boxes |
Working it
- 1
Look at the process
Before anything else: could the process actually be there. A wet well at the top of its range or a pressure at zero during a shutdown is real. Field indicators, a portable instrument, or the operators know.
- 2
Measure the current
A meter in series at the receiver terminals, or a clamp meter for milliamps. Compare with the table.
- 3
Read the transmitter
The local display or a handheld communicator: the measured value, the output current it thinks it is sending, any fault code, and the range.
- 4
Compare transmitter output with the measured current
If the transmitter says 12 milliamps and the meter says 0, the loop is open between them. If both say 20, the transmitter is driving the rail and the reason is in the transmitter or the process.
- 5
Check the range
Transmitter lower and upper range values against the design and the controller scaling. A range changed during calibration or a replacement with factory defaults is common.
- 6
Check the input
Module channel diagnostics, channel range setting, raw counts, scaling, and any clamp in the logic.
- 7
Fix and verify
Sweep the transmitter output through the range with a simulator and confirm the controller value follows.
When the process is really there
A signal that pegs because the process exceeds the range is a design finding rather than an instrument fault. A range that fit the process at design has been outgrown by a new pump, a new setpoint, or a changed operation, and the fix is a new range in the transmitter and in every place that scales it, with the change documented. A signal that pegs briefly during an upset and returns is doing its job; the alarm on the rail is what the design intends.
Frequently asked questions
- The transmitter says 20.0 and the process is nowhere near full scale.
- The transmitter has either the wrong range, a sensor that has failed toward full scale, or a fault that it reports as full scale rather than as a fault current. The transmitter configuration and diagnostics say which; a sensor fault is confirmed by applying a known input.
- Why does my controller show 3.6 mA as a valid low reading instead of a fault?
- Because the input scaling extends below 4 milliamps and nothing in the logic checks for under-range. The input module under-range flag, or a comparison against 3.8 milliamps, should drive a bad-quality flag and an alarm rather than a value.
- The signal pegs high when a nearby motor starts.
- That is noise or a supply sag rather than a rail: a common-mode surge on the loop, a supply that dips under the start, or a ground path that shifts. Measure the loop current during the start with a meter that records minimum and maximum.
- Can a bad loop supply make a signal peg?
- A supply without enough voltage for the loop resistance cannot drive 20 milliamps and the signal saturates below full scale; a supply that fails leaves the loop at 0. Measure the supply at the transmitter with the loop at 20 milliamps.
Related topics
- Transmitter Reads Wrong ValueThe reading is steady, plausible, and wrong. How to prove it against a reference, then separate a scaling mismatch, a range change, a zero shift, an installation effect, and a genuine transmitter fault, with the order of checks that finds it fastest.
- Loop Powers Up but Reads ZeroThe transmitter is lit and the controller shows zero, so loop current is not reaching the input: a loop wired for power but not signal, an active and passive mismatch, a missing jumper, an unconfigured channel, a blown fuse, or a transmitter sending nothing.
- Signal ValidationCatching a failed analog input in logic before it runs a pump on a dead transmitter: range checks, module status bits, frozen-value detection, rate checks, and what the program does with a bad value.
- 4-20 mA Signals from the Instrument SideHow a 4-20 mA current loop is powered and wired at the transmitter, why the loop resistance budget matters, and how to check a loop with a meter.
- How to Test a 4-20 mA LoopProve a current loop end to end with a meter and a calibrator, without interrupting a process you were not authorized to interrupt.
- Analog Scaling: Raw Counts to Engineering UnitsThe arithmetic that turns an analog card reading into feet, psi, or gallons per minute — plus the range mismatches that silently corrupt it.
Direct contact
Have a controls question?
Reach Eric Sullivan directly about anything on this site, a controls or automation topic, or one of his personal projects.