The short answer
How to Test a 4-20 mA Loop
Test a 4-20 mA loop by first measuring non-intrusively, reading voltage across the known input resistor, where 1.000 V across 250 ohms equals 4 mA and 5.000 V equals 20 mA. If you need the transmitter output directly, break the loop and insert a meter in series on milliamps. To test the receiving end, disconnect the transmitter and inject known currents with a calibrator.
Key points
- Measure voltage across the sense resistor first; it interrupts nothing.
- A series milliamp measurement opens the loop and the receiver will see a fault.
- Injecting current tests the receiving half; measuring tests the sending half.
- Do both halves separately and you will know which side owns the problem.
- Always tell operations before you drive a control input with a value you invented.
What you need
- Digital multimeter with a milliamp range
- Loop calibrator, source and measure
- The loop sheet or wiring diagram for this circuit
- HART communicator if the transmitter supports it
- Small screwdriver and a way to safely land a lifted conductor
Method 1: measure without interrupting
- 1
Identify the sense resistor
Most analog inputs present a known resistance, commonly 250 ohms. Some panels include a dedicated test resistor. Confirm the value from the module documentation rather than assuming.
- 2
Measure DC volts across it
Set the meter to DC volts and place the leads across the resistor or the input terminals. Nothing is interrupted and the process is unaffected.
- 3
Convert to current
Divide voltage by resistance. Across 250 ohms, 1.000 V is 4 mA, 3.000 V is 12 mA, and 5.000 V is 20 mA.
- 4
Compare against the HMI
Convert your measured current to a percentage of span and compare it against what the HMI shows. If they agree, the scaling is right and any error is upstream at the transmitter or in the field.
I (mA) = V_measured ÷ R_sense × 1000
- V_measured — volts across the sense resistor
- R_sense — resistance in ohms, commonly 250
Method 2: series measurement of the actual loop current
- 5
Prepare
Confirm the loop is in manual or otherwise safe to interrupt. Set the meter to DC milliamps and move the red lead to the milliamp jack. Verify the meter fuse is good, because a blown milliamp fuse reads zero and will send you chasing a fault that does not exist.
- 6
Use test jacks if the transmitter has them
Many transmitters include test terminals that insert the meter without opening the loop. Use them when available; this is the whole reason they exist.
- 7
Otherwise break the loop and insert the meter
Lift one conductor at a terminal, place the meter in series between the lifted wire and the terminal, and restore the circuit through the meter. Reading current in parallel across a live loop will blow the meter fuse and may damage the meter.
- 8
Read and compare
The measured current is what the transmitter is sending. Compare it against the transmitter local display and against the HMI value. Any disagreement now tells you exactly which segment owns the problem.
- 9
Restore carefully
Remove the meter, restore the conductor, torque the terminal, and confirm the reading returns to normal before you leave the panel.
Method 3: inject to test the receiving side
Disconnect the transmitter, connect a loop calibrator in source mode in its place, and drive known currents. This isolates everything downstream of the transmitter: the wiring, the input card, the scaling, and the display.
| Inject | Expected percent | Expected HMI value |
|---|---|---|
| 4.00 mA | 0% | 0.0 ft |
| 8.00 mA | 25% | 6.25 ft |
| 12.00 mA | 50% | 12.5 ft |
| 16.00 mA | 75% | 18.75 ft |
| 20.00 mA | 100% | 25.0 ft |
| 3.5 mA | Below range | Fault indication, not a level |
| 21.5 mA | Above range | Fault indication, not a level |
Reading the results
| Transmitter output | PLC raw value | Conclusion |
|---|---|---|
| Correct | Correct, HMI wrong | Scaling or display configuration |
| Correct | Wrong | Wiring, input card, or channel configuration |
| Wrong | Matches the wrong value | Transmitter calibration or process connection |
| 0 mA | 0 mA | Open loop: supply, wiring, or a dead transmitter |
| Correct at low, clipped at high | Same | Insufficient loop voltage for total resistance |
| Injection reads correctly at all points | Same | Receiving side is fine; the problem is the transmitter or the process |
Frequently asked questions
- Can I measure loop current without breaking the loop?
- Yes, in two ways: measure voltage across the known sense resistor and calculate, or use a true milliamp clamp meter. Transmitter test jacks also insert a meter without opening the circuit.
- Why does my meter read zero when the loop is clearly working?
- Check the meter fuse on the milliamp range first. A blown fuse reads zero and looks exactly like an open loop. Also confirm the red lead is in the milliamp jack, not the volts jack.
- What if the reading is correct at the panel but the HMI is wrong?
- The field and the input card are fine. The problem is scaling in the controller or configuration in the SCADA system. Check the card range setting first, then the scaling constants, then the SCADA tag.
- How do I test a loop-powered transmitter on the bench?
- Supply 24 VDC through a 250 ohm resistor in series with the transmitter, then measure voltage across the resistor to read current. That is a complete loop simulator built from two parts.
Related topics
- 4-20 mA Current LoopsWhy the industry standardized on current instead of voltage, how a two-wire loop is powered, what the live zero buys you, and how to read a loop with a meter.
- 4-20 mA Signal Is UnstableAn analog reading that will not settle. How to separate a genuine process swing from induced noise, a ground loop, or a loop running out of voltage.
- Loop ChecksProving every I/O point end to end before a system goes live: what a loop check is and is not, the three-point analog check, discrete and output checks, the two-person method with the sheet that records it, what to do with a point that fails, and why a loop check is not a calibration.
- How to Scale a 4-20 mA Input in a PLCTurn raw analog counts into engineering units, verify at three points, and add the validity checks that stop a failed transmitter from producing a believable number.
- How to Calibrate a Pressure TransmitterA five-point calibration with a pressure source and a reference: isolate and vent, record as-found, decide whether to adjust, trim the sensor and the output separately, verify as-left, and record it so the next calibration means something.
- How to Diagnose a Ground LoopProve that a noisy or offset analog signal is a ground loop, find the second ground, and fix it the right way: remove the extra ground, isolate the signal, or correct the shield termination. With the measurements that make the diagnosis certain.
Direct contact
Have a controls question?
Reach Eric Sullivan directly about anything on this site, a controls or automation topic, or one of his personal projects.